Ceramic vs Epoxy Sealed DC Contactors: Application Guide

Key Takeaway
A ceramic sealed DC contactor and an epoxy sealed DC contactor differ in how the arc chamber is closed, how well it keeps its fill gas, and which temperature and shock limits sit on the datasheet. Neither seal is the better choice on every ESS or PV circuit. The purchase order should name the part number whose datasheet covers the voltage, current, direction, and operation count you actually switch.
Table of Contents
When the RFQ Only Says Hermetic
Procurement teams often write one line: hermetic high-voltage DC contactor. Two quotations can both answer that line and still describe different machines. One chamber is a ceramic body with a metal braze. Another is a housing closed with epoxy. The gas inside, the leak rate, the magnet that blows the arc, and the number of times the contact may open under load are not implied by the word hermetic.
The pain shows up in the battery rack or the combiner, not in the bid table. An energy storage main contactor may sit closed for months and then have to open a high DC current when the battery management system trips. A precharge contactor closes into a capacitor through a resistor and may operate far more often at a lower current. A photovoltaic string may need a remote open at cold open-circuit voltage, with current in one direction only. A seal that is appropriate for one of those jobs can be the wrong reading of the datasheet for the next.
Treat ceramic and epoxy as construction families, not as a quality ranking. Ask what the seal is for: keeping a stated gas in the arc chamber for the life that the interrupting rating assumes. If the datasheet does not name the gas, the leak-rate limit, and the break duty, the seal adjective is not yet a specification.
What the Two Seals Change
A sealed DC contactor puts the contacts in a closed chamber so outside air does not feed the arc. The chamber has to survive heat from the arc, heat from the terminals, and years of temperature cycling. The two constructions close that chamber differently.
A ceramic sealed contactor uses a ceramic arc chamber joined to metal parts, typically by a metalized ceramic and a braze. That joint is the usual hermetic seal on contactors built for higher DC voltage. The chamber is commonly filled with hydrogen or a hydrogen mixture. Hydrogen cools the arc and helps it deionize, which is why a small chamber can publish a high break rating. The rating was measured with that fill in place. A cracked ceramic body or a leaked joint is not the same device the lab tested. Ceramic is also brittle. Mounting torque, busbar stress, and shock belong in the installation manual for that part number.
An epoxy sealed contactor closes the chamber or the housing with epoxy resin. Designs differ. Some are hermetic at a stated leak rate. Some are sealed against dust and moisture without the same leak-rate class as a ceramic-to-metal joint. The fill gas is whatever the datasheet names, often nitrogen, air, or another mix. Epoxy has its own temperature limit, including the region near the glass transition of the resin. Compare that limit with the ceramic part’s limit on the two datasheets. Do not assume a gap, and do not assume the epoxy part is adequate, until both sheets are in the file.
Switching duty is independent of the marketing name. Separate four currents when you read any sheet. Carrying current is what the closed contact can hold, usually with a stated temperature rise. Making current is what it can close onto. Breaking current is what it can open, at a stated voltage, a stated time constant or circuit type, and a stated number of operations. Short-circuit current is a further number, and many contactors do not claim it. A contactor that only carries, while a fuse clears faults, is a normal ESS arrangement. It is not a defect in the seal. It is a duty you must write down.
Direction matters as much as magnitude. Permanent-magnet blowouts are often polarized. The datasheet arrow is the breaking direction used in the test. Battery charge and discharge reverse the current. A photovoltaic string usually does not. A polarized contactor can still be the right part on a one-way PV circuit. On a bidirectional battery bus it is the right part only when the sheet says the break rating applies in both directions, or when you use the pole arrangement the sheet requires for reverse current.
Gas Fill, Switching Duty, and the Lines to Compare
Use the table as a reading guide. The cells describe what to look up. They are not a Weltrus catalog, and they are not a rule that one row wins.
| Question on the RFQ | Ceramic sealed chamber | Epoxy sealed chamber |
|---|---|---|
| How the chamber is closed | Ceramic body with a metal braze or equivalent ceramic-to-metal joint | Epoxy joint or epoxy-filled housing; confirm whether a leak rate is printed |
| Fill gas the break rating assumes | Commonly hydrogen or a hydrogen mixture; the datasheet names the actual fill | Commonly nitrogen, air, or another stated mix; do not infer hydrogen |
| What to do if the sheet is silent | Ask for fill gas, leak-rate limit, and the life assumption before you accept the break curve | Same request; a dust-tight housing is not automatically a hermetic gas seal |
| Temperature and mechanics | Follow the sheet; protect the ceramic from busbar stress and shock | Follow the sheet; compare the resin temperature limit with the enclosure temperature |
| Where either can be correct | Wherever that part number’s voltage, current, polarity, and operation count cover the duty | Wherever that part number’s voltage, current, polarity, and operation count cover the duty |

Read electrical life off the curve, not off the seal. A sheet may show one operation count at rated voltage and rated current, and a larger count at a lower current. Quote the point that matches your break. A mechanical life number, with no current, does not include arcing. Precharge duty and main-contactor duty should be checked at their own points.
Here is a buyer-side duty statement you can copy into an RFQ. It is not a Weltrus rating and not a suggestion that any stock part equals these numbers. “Main contactor: carry the continuous battery current in both directions; break that same current at the maximum battery voltage; electrical operations as required by the project; short-circuit current cleared by the fuse named in the coordination study unless the contactor sheet publishes a short-circuit rating you will use.” Put the project’s own amperes, volts, and operation count on the blank lines. The supplier answers with a part number and the datasheet page that meets each line.
Coil circuits are a datasheet block, not a family constant. Pickup voltage, dropout voltage, and holding power change with the part number. Many sealed contactors include an economizer so the coil does not sit at pickup power after it closes. Specify the control voltage you can supply. Ask the supplier to confirm that the offered part number accepts it. Do not reuse a coil voltage from a photograph of a different contactor.
Standards do not replace that page. IEC 60947-4-1 defines contactor duties, including DC-1 for resistive or slightly inductive loads. A DC-1 mark at one voltage is not a 1000 V battery break rating. Photovoltaic switches are often selected under IEC 60947-3 with category DC-PV1 or DC-PV2, which is a disconnect duty, not a ceramic-versus-epoxy choice. If the device you are buying is a contactor used as a remote PV open, say so, and require the DC break rating at the array’s maximum voltage.
What to Put on the ESS or PV DC RFQ
Write the circuit first. Then accept ceramic or epoxy when the part number covers the circuit. The RFQ should include every line below. Leave the seal line open unless a safety case or a mechanical constraint truly requires one construction.
- Circuit role: ESS main, ESS precharge, battery rack isolator, or PV remote disconnect. One role per line.
- Maximum voltage at which it must break, including cold open-circuit voltage on PV or the highest charge voltage on a battery.
- Continuous current in the closed state, and whether current reverses.
- Make and break current at that voltage, with the operation count. State the circuit: resistive, battery, or capacitor through a stated resistor.
- Short-circuit path: the fuse or breaker that clears faults, or a contactor short-circuit rating you intend to use. Do not leave this blank.
- Polarity: one direction or both. If the sheet is polarized, ask for the wiring that keeps the arc in the tested direction.
- Seal and gas: “ceramic or epoxy accepted if the datasheet covers the duty.” Ask for fill gas and leak-rate limit when the break rating depends on the fill.
- Auxiliary contacts the battery management system or inverter will read, and the coil control voltage available in the cabinet.
- Ambient, altitude, mounting, and terminal load. Altitude and enclosure temperature derates come from the datasheet of the part number.
- Evidence: datasheet revision, type-test basis for the break curve, and the certificate PDF whose scope lists that part number. No seal adjective replaces those files.
Damaged-part handling belongs in the same file when the fill is hydrogen. A cracked ceramic chamber can release the small gas volume it was built with. Follow the manufacturer’s instruction for a damaged unit. Do not treat a broken body as an ordinary contact-wear replacement and put it back into a rack.
What the Seal Does Not Decide
- It does not rank suppliers. Ceramic is not a standing upgrade over epoxy. Epoxy is not a standing compromise. The datasheet either covers the duty or it does not.
- It does not set coil voltage, price, or lead time. Those come from the quotation for the part number. This article does not publish them.
- It does not replace the fuse, the breaker, or the battery management trip scheme. The contactor opens when its coil circuit tells it to, within the break rating on the sheet.
- It does not transfer an ESS rating onto a PV string. Voltage, direction, and utilization category are checked again at the array maximum voltage.
- It does not make a polarized magnet bidirectional. Reverse current is allowed when the datasheet says so.
Send the Duty, Not Only the Seal Word
Share the circuit role, the maximum voltage, the current in each direction, and the operation count. Weltrus will answer with the part number and the datasheet pages that cover that duty, whether the chamber is ceramic or epoxy.
Frequently Asked Questions
Is a ceramic sealed DC contactor always a better choice than an epoxy sealed one?
No. The seal changes how the arc chamber holds its gas fill and how temperature and shock reach the contacts. The right part is the one whose datasheet covers the voltage, current, direction, and operation count of the circuit. An epoxy sealed part that meets that sheet can be the correct choice. A ceramic part whose sheet stops short of the duty is not made acceptable by the ceramic body.
Why does the fill gas matter on a sealed DC contactor?
The interrupting rating is demonstrated with the gas that was in the chamber during the type test. Hydrogen, or a hydrogen mixture, is common in ceramic hermetic chambers because it cools the arc. Nitrogen or air is common in other sealed designs. If the seal leaks, the tested gas is no longer the gas in service. Ask the datasheet for the fill gas, the leak-rate limit, and whether the break rating assumes that fill for the life of the part.
Can the same sealed contactor serve as the ESS main contactor and the precharge contactor?
Only if the datasheet for that part number covers both duties. A main contactor usually carries load current for long periods and must open under load when the battery management system commands it. A precharge contactor closes into a capacitor through a resistor, at a lower current and a different operation count. Write both duties on the RFQ as separate lines unless one part number is rated for both.
What should an ESS or PV RFQ say about coil voltage?
Name the control voltage available in the cabinet and ask the supplier to confirm pickup, dropout, and holding power from the datasheet of the offered part number. Do not copy a coil voltage from a different series. Many sealed contactors reduce holding power with an economizer on the contactor. That circuit is part of the part number, not a universal voltage.
Does a sealed DC contactor replace a fuse or a DC breaker?
No. A contactor makes and breaks the currents its datasheet lists. Short-circuit current is cleared by the fuse or breaker named in the coordination study, unless the contactor datasheet itself publishes a short-circuit rating at that voltage and the study uses it. Sealing type does not add a short-circuit rating that the sheet does not print.




