Specify a Stacked Residential ESS Before It Lands

Key Takeaway
A stacked residential energy storage system is a floor battery cabinet with the inverter enclosure set on top, so power and energy share one footprint. The photo shows that layout. It does not state kilowatts, usable kilowatt-hours, phase, ingress rating, or mass. Those lines still have to be on the order.
What the Stack Actually Is
The hardware in front of a buyer is two boxes, not one welded tank. The lower enclosure is a tall white battery cabinet on casters. The upper enclosure is the inverter head: a separate case, a front display, and controls on that display. Both cases carry the Weltrus mark. They leave the factory as one residential assembly, and they occupy the floor area of the cabinet plus the height of the head.
That layout is a siting choice as much as a product choice. One footprint is easier in a utility room that has floor and a clear front, and harder in a design that wanted the inverter on an outside wall and the battery in a cupboard. The stack does not, by itself, tell you which of those rooms you have.
Read the two nameplates as two products that ship together. Alternating-current power, backup output, and any photovoltaic input live on the inverter head. Stored energy and the battery voltage class live on the cabinet. A quotation that prints a single “system size” without saying which number is power and which number is energy is not yet a specification.
Why a “Home Battery” Line Is Not a Layout
Distributors and installers lose time when the purchase order says home battery, and the room was drawn for something else. Three mismatches show up after the crate is already on the truck.
The first is class. A floor stack for a house is not a commercial all-in-one cabinet in the hundred-kilowatt range. The commercial cabinet needs a plant room, a different mass, and a different one-line. Putting residential clearance notes on that cabinet, or putting commercial loading notes on this stack, sends the wrong crew and the wrong drawing.
The second is phase and backup scope. Many houses are single-phase. Light commercial services are often three-phase. A stack that was quoted against the wrong service will not become the right service because the cabinet fits through the door. Whole-home backup and essential-load backup are also different output designs. The display on the head does not answer that question.
The third is the wall. The unit in the photograph stands indoors, on a hard floor, near ordinary wall outlets. Those outlets are the room. They are not the grid connection of the storage system, and they are not a permit to plug the inverter into a general-purpose socket. The alternating-current landing is the breaker, the cable size, and the grid code on the project file.
What You Can Confirm, and What You Cannot
Use the hardware photo to lock the layout. Use the data sheet, the packing list, and the installation manual to lock the numbers. Mixing those sources is how a Y-class mark on a crate gets copied in as the cabinet weight, or how a round feature on a door gets described as a cooling specification nobody printed.
| Question | This stack shows | Still required on the file |
|---|---|---|
| Layout | Inverter head on a floor cabinet | Whether the two enclosures may be separated |
| Power | An inverter enclosure with a display | Rated kilowatts, phase, and grid voltage |
| Energy | A battery cabinet under the head | Usable kilowatt-hours and voltage class |
| Move | Casters on a level hard floor | Packing-list mass, door width, and lift method |
| Place | Indoor, against a wall | Ingress rating of each enclosure, and clearances |
| Connect | No visible field wiring in the photo | Breaker, cable path, and any photovoltaic input |
Which Layout the Room Can Accept
Pick the layout before you pick a wattage slogan. The stack is one of four patterns that show up on residential and light commercial requests. They are not interchangeable after the concrete, the wall, or the switchboard is finished.
| Layout | Fits when | Stop when |
|---|---|---|
| Floor cabinet with inverter head | One indoor footprint, level floor, front access to the display | The inverter must live outdoors, or the floor load is unknown |
| Wall hybrid inverter and a separate battery | The battery location and the inverter location are different walls or rooms | You assumed this stack splits, and the manual says it ships as one assembly |
| Outdoor-rated inverter, battery indoors | The inverter nameplate carries the outdoor ingress rating the wall needs | You only have an indoor photograph and no ingress line for the head |
| Commercial all-in-one cabinet | The one-line is a commercial plant, not a house service | The request is a residential stack and the drawing is a hundred-kilowatt room |
If the project is still choosing single-phase or three-phase, settle that on the service, not on the cabinet color. The same rule applies to stored energy: a sizing sheet that starts from load, backup hours, and photovoltaic production is a different document from this layout check. Do not let a footprint decision pretend to be a kilowatt-hour calculation.
Site Checks Before the Cabinet Leaves the Crate
Arrival handling of the plywood crate is a separate note: edges, latches, and the lithium marks. This list starts once someone is about to stand the cabinet up and give it a place to live.
- Path and door. The cabinet is tall once the head is on it, and it is as wide as a floor appliance. Measure the door, the turn, and the finished height against the drawing. A photo against a wall is not a dimension.
- Floor. Casters roll on a level hard surface. They do not forgive a step, a soft deck, or a slope. The mass for the floor design is the packing-list figure for that serial, including the head if the head is already fitted. Do not invent a kilogram from the picture, and do not reuse a packaging approval code as the scale weight.
- Front working space. The display and the buttons are on the face of the inverter head. A person has to stand there to read alarms and to confirm the unit. Pushing the face into a corridor so the side almost fits hides the only interface the installer has.
- Air and the joint between the boxes. The head is an electronic enclosure on top of a battery enclosure. Leave the clearance the manual gives for cooling air, and find out whether cables between the head and the cabinet exit at the rear, the side, or the joint. A cabinet shoved against its only cable exit cannot be commissioned without being moved again.
- Wet area and outdoors. The photograph is an indoor set. Outdoor placement is allowed only when each enclosure’s ingress rating, sun, and drain path are written down. One indoor picture does not rate the head for a wet wall.
- Finished restraint. Rolling the cabinet into position is not the same as leaving it on casters for the life of the system. If the site needs a fixed base, a seismic detail, or a public-room guard, that detail has to be in the order and in the manual. Casters are a move aid.
- Two-person lift, then roll. Getting the cabinet out of the crate and standing it up is a two-person job, or a lift rated above the packing-list mass. Casters are for the level floor after it is upright. They are not a reason to skip the second person on the lift.
Lines That Belong on the Request
Send these as separate lines. A dealer who merges them into one “home battery kit” sentence will still have to split them when the installer asks for the breaker and the floor load.
| Line | Why it is its own line | Where it is written |
|---|---|---|
| Rated alternating-current power | Power is the inverter, not the battery cabinet | Inverter nameplate and data sheet |
| Usable energy | Energy is the cabinet, and nameplate capacity is not always the usable figure | Battery data sheet, with the conditions stated |
| Battery voltage class | The head and the cabinet have to be the pair that was tested together | Both data sheets, matched as a pair |
| Phase and grid voltage | The house or shop service is already built | One-line and inverter nameplate |
| Backup scope | Whole home and essential loads are different output designs | One-line diagram and inverter manual |
| Photovoltaic input, if the head has one | A battery cabinet does not disclose string voltage or tracker count | Inverter data sheet; leave blank if the head has no photovoltaic input |
| Ingress rating of each enclosure | Two boxes can have two ratings | Each nameplate |
| Mass and outer size | Door, floor, and lift all use the drawing, not the photo | Packing list and dimension drawing |
| Cable between head and cabinet | Factory fitted and field fitted change the install hours | Installation manual |
| Casters and fixing | Move aid and finished restraint are different | Installation manual and site specification |
| Grid code and export limit | Interconnection is a project setting, not a cabinet color | Utility file and inverter settings list |
| Warranty split | Inverter years and battery years are often different sheets | Warranty terms for each enclosure |
How to read the power line without guessing a model
This note does not publish a model code or a kilowatt rating, because the photograph does not contain one. If you are choosing among home inverter classes, compare the service and the backup load on the data sheet you were quoted, then check phase separately. Choosing a six kilowatt class or an eight kilowatt class is the same kind of decision for a wall hybrid and for this stack. Cabinet height does not settle it.
Ask whether the backup output can carry the loads on the essential panel at the same time, and whether the grid input matches the voltage already in the switchboard. A unit that is fine on power and wrong on voltage is still the wrong unit. Record the answer next to the one-line, not in a chat message that will not be on site.
What This Note Does Not Decide
- It does not size the battery. Backup hours, night load, and photovoltaic production belong on a sizing sheet. A footprint is not a kilowatt-hour.
- It does not choose single-phase or three-phase. That follows the service. Confirm it before the head is released to production.
- It does not rate the room as outdoor. Ingress, sun, and drainage have to be printed. An indoor photograph is not a rating.
- It does not replace the crate check. Edges, latches, and lithium marks are how you know the cabinet that arrived is the cabinet that shipped. Do that before you argue about the display.
- It does not authorize a general-purpose wall outlet as the grid connection. Land the alternating-current side on the breaker and cable the design calls for.
- It does not cover a commercial hundred-kilowatt cabinet. Different mass, different room, different protection. Keep the files apart.
Send the Room and the Service, Not Only a Photo
For a Weltrus residential stack, send the service phase and voltage, the backup load list, the door and floor limits, and whether the inverter must stay indoors. Weltrus will match the head and the cabinet as a pair, and will say if this footprint is the wrong layout.
Frequently Asked Questions
Is the inverter part of the battery cabinet?
On this Weltrus residential stack the inverter is a separate enclosure sitting on the battery cabinet. Power belongs on the inverter nameplate. Usable energy belongs on the battery data sheet. Copying one number onto both lines puts the wrong figure on the order.
Can the casters stay after installation?
Casters let two people roll the cabinet on a level hard floor after it is upright. They are not a seismic restraint and they are not a substitute for the fixing method in the installation manual. If the finished site must be fixed, specify that before the unit ships.
Does a stacked home battery replace a wall hybrid inverter?
Only when the room, the service, and the backup scope match a floor stack. A wall hybrid plus a separate battery is the better layout when the inverter must sit outdoors, or when the battery and the inverter cannot share one footprint. Confirm that this stack can be split before you design them apart.
Is this the same product as a commercial all-in-one cabinet?
No. A residential stack is a home-scale floor cabinet with an inverter head. A commercial all-in-one cabinet in the hundred-kilowatt class is a different room, a different mass, and a different one-line. Do not reuse the site notes from one class on the other.




